Cub-fuser-D

                                      undefined

undefined

Cub-fuser-D

 

  • Interior 510mm x 510mm x 330mm.
  • 4.5kw single phase..
  • 960c maximum temperature
  • Quartz tube "infra-red" heating system.
  • Stainless Steel.
  • lid lift assist.
  • KCR16 digital programer with 10 programs, 16 segments in each program.
  • Can be set in Centigrade or Fahrenheit
  • Fast react thermocouple.
  • Non ceramic fibre lid section.
  • Light weight refractory brick base.
  • 110mm recessed floor
  • Kilncare unique KCX over temperature, in built protection..
  • Large vent/spy hole with spring return, anti dust flap.
  • FOUR YEARS GUARANTEE on ALL parts INCLUDING the elements.
  • Built and designed by Kilncare in the U.K.

 

The Cub-fuser-D is the final piece in the "fuser" familly jigsaw and completes the line up for the most advanced fusing/slumping kilns available today.

The Cub-fuser-D has all of the features that have become ex[ected from the "fuser" familly and is basically a reduced width Pro-fuser. This allows customers with limited space, but larger requirements than the Hobbyfuser can supply, to fulfill thier artistic potential.


undefined

 

There are two features new to the Cub-fuser-D.
Firstly, it is the first kiln to be fitted with the new Kilncare KCX electronic over temperature safety device.
The KCX is a standard fit on the kiln and is part of the kilns wiring making the Cub-fuser-D unique in having designated electronic protection as part of the kiln rather than relying on the temperature controller.

Of course, the KCR16 also has its own protection circuits to double up on the safety of this kiln.

The KCX on the Cub-fuser-D is preset to 970c. If the kiln temperature reaches this point, then the kiln will be shut off completely and will not start until the kiln is re-powered.


Secondly, the Cub-fuser-D is the first kiln to have its Kilncare 3 year guarantee on ALL parts, including the elements, extended to an industry leading 4 years!!!!
This guarantee makes the Cub-fuser-D the most comprehensively covered kiln available from any manufacturer.

 

 

undefined  Stainless Steel lid assist springs.

 

The lifting and closing of the lid is assisted by a pair of specifically manufactured and designed Stainless Steel coil springs at the rear of the kiln. These are accompanied by a pair of specially designed gas springs to assist with the lower part of the lift/close movement.

 

The kiln lid is made from stainless steel and lined out with non-ceramic fibre,  This method of insulation removes the danger of brick dust or particles dropping onto the glass, so making for a very clean firing environment. It also makes the Cub-fuser-D incredibly resistant to shock damage.
This lid construction enables the Cub-fuser-D to hold back the heat when needed but still release heat rapidly during the all important cooldown period.

 

 
undefined  Angled vent/spy hole with spring assist.

The front of the kiln has a large vent/peep hole which is closed using a spring assisted flap which houses our unique, anti-dust insulation pad which is taken from our larger fusing kiln models.
The vent/peep hole is angled so that the floor of the kiln and more importantly, your glass, can be seen.

 

 

undefined  Quartz "Infra-red" element system

 

The heating system is in the roof only and utilises the latest technology "infra-red" quartz tube heating elements. This method is extremely hard wearing and strong, yet in the event of an element failure the tubes are both easy and cheap to replace.
The elements are switched off when the lid is opened by an automatic safety switch.

 

The metal work of the base is Stainless steel.

  
undefined
                                                Flat loading floor with recess

The pre-fitted control is the KCR16, which is detailed on the controls section of our web site. It has 10 programs, each having 16 segments. each segment consists of 1 x rate of climb, 1 x target temperature and 1 x dwell/hold.
9 of the KCR16 programs are pre-set with useful glass cycles for fusing and slumping float, Bullseye and Spectrum glass as well as a Bottle slumping program and a couple of stain cycles. If these programs are not as you would like them, simply alter them to your own preferences.

The KCR15 also has Program Pause, Segment Forwarding and can be set in Centigrade or Fahrenheit.
The KCR16 has its own temperature monitoring relay that will shut the kiln down in the event of an overfire situation.


The KCR16 gets its data from an ultra-fast response, stainless steel thermocouple meaning no lag between the kiln temperature and the KCR16s control.
The fact that the thermocouple is stainless steel means it is also resilient to accidental damage.

 

 

We build the Cub-fuserr-D here, in Stoke on Trent, so parts and service will never be an issue.

 

 

 


Cub-fuser-D Stand (Optional)


         undefined                


             

The Cub-fuser-D stand has two shelves, one for the kiln to sit on and one for your own use. It raises the kiln by 650mm to a comfortable height.
It is made of steel and is powder coated in our Ultra-marine blue.
The stand is supplied ready for assembly.

 
Lockable wheels for Cub-fuser-D Stand (optional)

 

          undefined

A further option for the Cub-fuser-D stand is locking, swiveling wheels.

The wheels are pre-fitted at our factory but the stand is still sent out ready for assembly.


KCR16 and KCR16 Stand (Included)

 undefined         undefined

The KCR16 can be removed from its stand mounted holster to enable it to be hand held for easy and comfortable programming.

MODEL

INTERNAL SIZE
WxDxH (mm)

EXTERNAL SIZE
WxDxH (mm)

kW   POWER  SUPPLY

 

 

Cub-fuser-D

 

 

510 x 510 x 330

 

 

895 x 810 x 635

 

 

4.5kW

   

240v

 

undefined 0% finance for 4 mounths using Paypal Credit.

 

Price includes UK delivery and V.A.T.
There may be a delivery surcharge for outlying areas.

Cub-fuser-D packages

Please note......if you opt for standard delivery, this is via a independent transport or courier.
The obligation of the delivery company is to get the kiln safely to your address and to deliver to ground level. However, you will need to make your own arrangements to get the kiln to your final site position. Delivery drivers will not assist in getting the kilns through narrow gates e.t.c. The independent drivers are not and cannot be contracted to help site the kiln in your final position.
For assisted delivery please contact us for a quote on Kilncare personal delivery.


The kiln will arrive packaged on a pallet.

The pallet dimensions are 104cm x 168cm.

The Cub-fuser-D weighs 105kg.

 

Follow us on Facebook. Click HERE.

Cub-fuser-D

 

  • Interior 510mm x 510mm x 330mm.
  • 4.5kw single phase..
  • 960c maximum temperature
  • Quartz tube "infra-red" heating system.
  • Stainless Steel.
  • lid lift assist.
  • KCR16 digital programer with 10 programs, 16 segments in each program.
  • Can be set in Centigrade or Fahrenheit
  • Fast react thermocouple.
  • Non ceramic fibre lid section.
  • Light weight refractory brick base.
  • 110mm recessed floor
  • Kilncare unique KCX over temperature, in built protection..
  • Large vent/spy hole with spring return, anti dust flap.
  • FOUR YEARS GUARANTEE on ALL parts INCLUDING the elements.
  • Built and designed by Kilncare in the U.K.

 

The Cub-fuser-D is the final piece in the "fuser" familly jigsaw and completes the line up for the most advanced fusing/slumping kilns available today.

The Cub-fuser-D has all of the features that have become ex[ected from the "fuser" familly and is basically a reduced width Pro-fuser. This allows customers with limited space, but larger requirements than the Hobbyfuser can supply, to fulfill thier artistic potential.

undefined

There are two features new to the Cub-fuser-D.
Firstly, it is the first kiln to be fitted with the new Kilncare KCX electronic over temperature safety device.
The KCX is a standard fit on the kiln and is part of the kilns wiring making the Cub-fuser-D unique in having designated electronic protection as part of the kiln rather than relying on the temperature controller.
Of course, the KCR16 also has its own protection circuits to double up on the safety of this kiln.

The KCX on the Cub-fuser-D is preset to 970c. If the kiln temperature reaches this point, then the kiln will be shut off completely and will not start until the kiln is re-powered.

Secondly, the Cub-fuser-D is the first kiln to have its Kilncare 3 year guarantee on ALL parts, including the elements, extended to an industry leading 4 years!!!!
This guarantee makes the Cub-fuser-D the most comprehensively covered kiln available from any manufacturer.

undefined  Stainless Steel lid assist springs.

 

The lifting and closing of the lid is assisted by a pair of specifically manufactured and designed Stainless Steel coil springs at the rear of the kiln. These are accompanied by a pair of specially designed gas springs to assist with the lower part of the lift/close movement.

 

The kiln lid is made from stainless steel and lined out with non-ceramic fibre,  This method of insulation removes the danger of brick dust or particles dropping onto the glass, so making for a very clean firing environment. It also makes the Cub-fuser-D incredibly resistant to shock damage.
This lid construction enables the Cub-fuser-D to hold back the heat when needed but still release heat rapidly during the all important cooldown period.

 

 
undefined  Angled vent/spy hole with spring assist.

The front of the kiln has a large vent/peep hole which is closed using a spring assisted flap which houses our unique, anti-dust insulation pad which is taken from our larger fusing kiln models.
The vent/peep hole is angled so that the floor of the kiln and more importantly, your glass, can be seen.

 

 

undefined  Quartz "Infra-red" element system

 

The heating system is in the roof only and utilises the latest technology "infra-red" quartz tube heating elements. This method is extremely hard wearing and strong, yet in the event of an element failure the tubes are both easy and cheap to replace.
The elements are switched off when the lid is opened by an automatic safety switch.

 

The metal work of the base is Stainless steel.

  
undefined
                                                Flat loading floor with recess

The pre-fitted control is the KCR16, which is detailed on the controls section of our web site. It has 10 programs, each having 16 segments. each segment consists of 1 x rate of climb, 1 x target temperature and 1 x dwell/hold.
9 of the KCR16 programs are pre-set with useful glass cycles for fusing and slumping float, Bullseye and Spectrum glass as well as a Bottle slumping program and a couple of stain cycles. If these programs are not as you would like them, simply alter them to your own preferences.

The KCR15 also has Program Pause, Segment Forwarding and can be set in Centigrade or Fahrenheit.
The KCR16 has its own temperature monitoring relay that will shut the kiln down in the event of an overfire situation.


The KCR16 gets its data from an ultra-fast response, stainless steel thermocouple meaning no lag between the kiln temperature and the KCR16s control.
The fact that the thermocouple is stainless steel means it is also resilient to accidental damage.

 

 

We build the Cub-fuserr-D here, in Stoke on Trent, so parts and service will never be an issue.

 

 

 


Cub-fuser-D Stand (Optional)


         undefined                


             

The Cub-fuser-D stand has two shelves, one for the kiln to sit on and one for your own use. It raises the kiln by 650mm to a comfortable height.
It is made of steel and is powder coated in our Ultra-marine blue.
The stand is supplied ready for assembly.

 
Lockable wheels for Cub-fuser-D Stand (optional)

 

          undefined

A further option for the Cub-fuser-D stand is locking, swiveling wheels.

The wheels are pre-fitted at our factory but the stand is still sent out ready for assembly.


KCR16 and KCR16 Stand (Included)

 undefined         undefined

The KCR16 can be removed from its stand mounted holster to enable it to be hand held for easy and comfortable programming.

     
     

 

Follow us on Facebook. Click HERE.

 

undefined 0% finance for 4 mounths using Paypal Credit.

 

Price includes UK delivery and V.A.T.
There may be a delivery surcharge for outlying areas.

Cub-fuser-D packages

Please note......if you opt for standard delivery, this is via a independent transport or courier.
The obligation of the delivery company is to get the kiln safely to your address and to deliver to ground level. However, you will need to make your own arrangements to get the kiln to your final site position. Delivery drivers will not assist in getting the kilns through narrow gates e.t.c. The independent drivers are not and cannot be contracted to help site the kiln in your final position.
For assisted delivery please contact us for a quote on Kilncare personal delivery.


The kiln will arrive packaged on a pallet.

The pallet dimensions are 104cm x 168cm.

The Cub-fuser-D weighs 105kg.

 

Follow us on Facebook. Click HERE.

MODEL

INTERNAL SIZE
WxDxH (mm)

EXTERNAL SIZE
WxDxH (mm)

kW   POWER  SUPPLY

 

 

Cub-fuser-D

 

 

510 x 510 x 330

 

 

895 x 810 x 635

 

 

4.5kW

   

240v

         
         
         
         
  • View Product Image
  • View Information
  • View Specification
click icons for more information